HEF Datasheet, HEF PDF, HEF Data sheet, HEF manual, HEF pdf, HEF, datenblatt, Electronics HEF, alldatasheet, free. 15 Apr Data sheet acquired from Harris Semiconductor. SCHSC − Revised October HCDB consists of an oscillator section and CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator. CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator – CDB. Datasheet.
|Published (Last):||21 September 2016|
|PDF File Size:||13.27 Mb|
|ePub File Size:||9.59 Mb|
|Price:||Free* [*Free Regsitration Required]|
Eventually the output hef4060 datasheet IC10C goes high when a button is pressed. The Hours Counter And now the hours counter.
Hef4060 datasheet is built on pad board using Road Runner wiring to connect all the components together. When the second decade reaches 6 the output hef4060 datasheet IC10A dataxheet go low. But this time the maximum count value is limited to Let’s start simple, the buttons, which are used to set the time.
While the clock is in SET mode hef4060 datasheet won’t come any carry pulses from the minutes counter and that signal is constantly high.
At the end it will produce an accurate frequency of 2Hz on output pin 3. Next stop, the minutes counter. This counter is also formed by 2 decade counters. Now IC9D will inverse hef4060 datasheet pulses coming from the push button. It uses a The Time Base IC2 forms the time base oscillator and first pre-scaler stage.
Результаты поиска для HEF4060
We haven’t talked about the carry hef4060 datasheet the seconds counter to the minutes counter yet. We need 1Hz, not 2Hz, to feed hef4060 datasheet our seconds counter. IC2 also contains a 14 bit divider chain. The output pulse from IC10A also goes out to the minutes counter, which has datahseet be advanced at every overflow of the seconds counter.
This will produce a high going reset pulse on the output of IC10B. This allows you to accurately synchronize hef4060 datasheet clock with a known good time source. This pulse is used to flash the colon between the hour digits and the minute digits on the display.
Navigation How to navigate Sponsors Please consider clicking on the Support Me button to show your appreciation. We’ll have to tell the clock what time it is when it has hef4060 datasheet all its power anyway.
This signal ratasheet fed to the seconds counter, as described below. From then on the flip-flop remains in that state, hef4060 datasheet the hours counter is reset to 0 again.
hef, buy hef, specification & datasheets
I have covered the time base and the counters here. TP1 is a test point at which you can measure the buffered It hef4060 datasheet really matter whether we use a rising or falling edge here because this carry pulse is very short.
Otherwise the roll over of the minutes counter would advance the hours counter too. Hef4060 datasheet inputs of IC10D are hef400 when the button is pressed, making its output low. This page will describe sheet one in detail, while the hef4060 datasheet page will describe sheet number two. This helps to tune the frequency of the time base to the correct value.
When the hours counter is reset, so is the flip-flop, making its Q output high. IC4A divides the 1Hz pulse by In SET mode the SET signal is high, and the seconds to minutes carry can never occur because the seconds counter is held hef4006 reset.
It is spread over two sheets, one sheet covers the time hef4060 datasheet and the seconds, minutes and hours counters. My way of keeping this site alive.
HEF Datasheet catalog
This will increase the stability hef4060 datasheet your clock. This reset pulse is also used as carry to the hours counter.
Both buttons have a debouncing capacitor hef4060 datasheet parallel to make sure that every button press results in just one pulse. On the next page I’ll explain the display circuit and power supply of the hdf4060.
The oscillator part is built as described in the HEF data sheet. It also produces hef4060 datasheet other division ratios.
It’s a bed side table clock, I don’t need it to light up the entire room at night, you know. The precision of the resistor value has no effect on the precision of the time base B.
It’s output Q0 hef4060 datasheet the first decade counter IC4A. The clock can be in one of two different modes, in Run hef4060 datasheet or in Set mode. The Minutes Counter Next stop, the minutes counter. Therefore IC9C will inversely follow the low going carry signal from the minutes counter. We are only interested in two others, the Hz and the 64Hz outputs, which are used in the display section of the clock.
When the clock is switched to SET mode hef4060 datasheet, the SET line goes low, which keeps the reset line to the seconds counter constantly hef40660, preventing the seconds counter to count.