FREQROL FR-SF PDF

Mitsubishi FR-SF spindle drive manual. Uploaded by. Zeynel Ulusoy. USA- E* AC SPINDLE DRIV TROUBLESHOOTING, i A D V A N C E D AND . Hi Guys, I Replaced the power supply (SF-PW) on this spindle drive about 3 months ago and it was working fine for the last 3 months. For the. Mitsubishi vector Inverter Motor (SF-V5RU Series), English, , MB. FR -A/F/E/D SERIES TECHNICAL MANUAL, English,

Author: Tegore Gardasho
Country: Ethiopia
Language: English (Spanish)
Genre: Art
Published (Last): 7 July 2006
Pages: 349
PDF File Size: 12.75 Mb
ePub File Size: 7.10 Mb
ISBN: 352-5-74399-844-4
Downloads: 56146
Price: Free* [*Free Regsitration Required]
Uploader: Mole

Al – CO Parameter 3: OFF Position of dip switch.

MITSUBISHI FREQROL Spindle drive

When 0 is set, the magnification becomes 1. Generally, when conducting a test, do not ground the case of any test apparatus. The load is heavy and 1 Set the spindle parameter 0RS2 the spindle fr-af dur- bit B to 1 to select strong ing tapping operation. The motor does not 1 Check and readjust the spindle orientation control circuyt by correctly rotate only referencing Chapter 7.

Inverters-FREQROL Manual Download | MITSUBISHI ELECTRIC FA

Spare part class C. Based on point c, move frqerol a. Parameter Description Setting range unit The spindle orientation direction, detec- tor installed direction, and motor rota- tion direction are set. Note To distinguish between a fault of the mechanical portion including the motor and that of the amplifier including the speed reference, take the following procedure. Standard value 20 2nd deceleration point range PGl: Torque meter Standard setting: Item Cause Check Remedy The motion balance of o Rotate the motor at a high o Improve the motion balance the machine is bad.

If 0 is set, it becomes 1 time.

Mitsubishi FR-SF: Industrial Automation, Control | eBay

Thanks Greg for all the information and diagonising the problem. For instructions of setting parameters, see Reference 1. There are three types of warnings as listed in the table. I have swopped them arround and I still get the same Alarm. You have the option to buy a product that is much cheaper than a Brand cr-sf version of the product and save money while benefiting from a quality product refurbishment process according to strict procedures prior to being offered for sale, fully tested and verified by skilled technicians in order to ensure quality of our repair and refurbishment process.

  CRUMB MAKROKOSMOS PDF

For the last 2 days the machine would just stop in mid greqrol with a spindle controller error on screen. Make setting sure that the setting conforms to the order list. Note 2 An example of the display is as follows.

A marked parameters are those being set by Mitsubishi.

Mitsubishi FR-SF

Note The stop position is controlled by a bit contact signal OlH to 12H and is controlled by the follow- ing equation. There was also an optocoupler blown on the main board.

The part should frewrol stocked by the machine manufacturer. BCD 3 digits not used In the case of the analog speed reference “0” or “1” is selected. The spindle does not o Check that the spindle parameters slimit and smax are not 0.

Your cart is empty. Red lead of circuit tester terminal: CCW Mckor forward rotation 1: Motor freqrop encoder 41 ISL orientation Hexadecimal notation 1: You have the option to buy a product that is much cheaper than the new or refurbished version of the product and save money while benefitting from a product that is worthy of the quality of the Cnc-Shopping Intl. Now you can access meau.

  AKTYVUS PARDAVIMAI PDF

As noted above connection and power supply problems are very common. SN deceleration 0 – msec ,PR time constant tion loop state. Check that it rotates for 10 frewrol until it comes fr-sff the hole bottom and returns to the start position. Note 2 An example of display is as follows: Note To check the occurrence o If the signal output is b If the alarm does not saturated when it exceeds occur, 10 V because a too high speed decrease the parameter is set, check that the volt- values of VKP and VKI.

Thanks for the help Guys Hi guys, The story so far The spindle parameters are categorized as parameters which are controlled on the NC side and those which are controlled on the spindle side where the spindle controller Freqorl is linked with the NC through the bus line. The data during orientation stop can be also changed.

Parameter Description Setting range unit 1 Control type such as gain during orien- tation stop is set. Load meter output 3v l The parameters being asterisked are set from the NC when the equipment is linked with the M series machine through the bus line. It represents 0 when no position loop is formed. This parameter becomes valid when t01 NOX is set to 2. To link the bus: Click here to sign up.

This item was removed from working machine and is being sold in good working condition. This part was pulled from a working machine. CCwelotor forward rotation