Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Ganos Arakazahn
Country: Liberia
Language: English (Spanish)
Genre: Business
Published (Last): 9 July 2017
Pages: 391
PDF File Size: 4.10 Mb
ePub File Size: 19.37 Mb
ISBN: 994-2-86996-662-3
Downloads: 26518
Price: Free* [*Free Regsitration Required]
Uploader: Zulushicage

NOTE 1—A typical ordering description is as follows: The SI equivalents are in parentheses and may be approximate.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

Originally published as A — It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

The following lubricants may be specied: B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0. All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification. The steel shall conform to the required chemical composition requirements. ICS Number Code An electroplated copper coating is often used.

The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.


Resistance to Intergranular Corrosion 8. The material shall also conform to the requirements as to mechanical properties.

ASTM A493 – 16

This standard has been approved for use by agencies of the Department of Asttm. This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

Link to Active This link will always route to the current Active version of the standard. Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

ASTM does not give any warranty express or implied or asgm any representation that the contents of this abstract are accurate, complete or up to date.

ASTM A493 Grade 384 annealed

A number in parentheses indicates the year of last reapproval. Soap is generally used. Such requirements may include, but are not limited to the following: The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades.


Historical Version s – view previous versions of standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. The producer should be consulted when qstm is required to tensile strength ranges other than those specied.

This abstract is a brief summary of the referenced standard. Current edition approved Jan. Packaging and Package Marking 9. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Material can be manufactured to tensile strength ranges other than those shown in Table 2. The following coatings may be specied: General Requirements for Delivery 4. Last previous edition A —